Autor según el artículo: Palmay, P; Puente, C; Haro, C; Bruno, JC; Coronas, A
Departamento: Enginyeria Mecànica
Autor/es de la URV: Bruno Argilaguet, Juan Carlos / Coronas Salcedo, Alberto / Palmay Paredes, Paul Gustavo
Palabras clave: Recycled polystyrene Pyrolytic oil Plastic waste Municipal waste residues Heavy fuel oil Cutter stock temperature styrene recovery recycled polystyrene pyrolytic oil polystyrene model kinetics heavy fuel oil energy degradation cutter stock catalytic pyrolysis
Resumen: In many countries, Heavy Fuel Oil (HFO) is still a common fuel in industrial applications due to its low price and high energy density. However, the complex and incomplete combustion of HFO results in high levels of emissions and low efficiency, which causes the search for additives to improve its properties without affecting its heating value. The present paper aims to use as an additive the liquid fraction from pyrolysis of the polystyrene for fuel oil, replacing conventional additives such as cutter stock, improving its fluidity without using heat to pump it. As for pyrolysis for obtaining pyrolytic oil, the effect of temperature on the chemical composition of the liquid fraction from the thermal pyrolysis of compact polystyrene was studied. PS pyrolysis was carried out in a temperature range between 350 to 450 °C at a heating rate of 15 °C min−1 in a batch type reactor, with a condensation system, in order to analyze the best fraction liquid yield. At 400 °C we obtained a liquid fraction of 81%. This product presented a kinematic viscosity of 1.026 mm2 s−1, a relative density of 0.935, a flash point of 24 °C, and a gross heating value of 48.5 MJ kg−1. Chromatographic analysis indicates that 75% by mass of the components corresponds to C6 to C20 hydrocarbons, showing the high generation of isomers of the polystyrene monomer and aromatic compounds. The product obtained is mixed with base fuel oil at 60 °C at 250 rpm for a period of one hour, in percentages of 10 to 50% by mass. The 10% mixture has properties very close to those required by the standard fuel oil, presenting a viscosity of 108 mm2 s−1 that adjusts to the requirements in burners for industrial applications; additionally, it has a Sulphur content lower than that of fuel oil without affecting its heating value.
Áreas temáticas: Zootecnia / recursos pesqueiros Renewable energy, sustainability and the environment Renewable energy, sustainability and the environm Interdisciplinar General computer science Fuel technology Engineering (miscellaneous) Engenharias iv Engenharias iii Engenharias ii Energy engineering and power technology Energy (miscellaneous) Energy & fuels Electrical and electronic engineering Economia Control and optimization Ciências ambientais Ciências agrárias i Ciência da computação Building and construction Biotecnología Biodiversidade Astronomia / física
Acceso a la licencia de uso: https://creativecommons.org/licenses/by/3.0/es/
Direcció de correo del autor: alberto.coronas@urv.cat paulgustavo.palmay@estudiants.urv.cat juancarlos.bruno@urv.cat
Identificador del autor: 0000-0002-6109-3680 0000-0001-7448-5416
Fecha de alta del registro: 2024-08-03
Versión del articulo depositado: info:eu-repo/semantics/publishedVersion
Enlace a la fuente original: https://www.mdpi.com/1996-1073/16/3/1485
URL Documento de licencia: https://repositori.urv.cat/ca/proteccio-de-dades/
Referencia al articulo segun fuente origial: Energies. 16 (3):
Referencia de l'ítem segons les normes APA: Palmay, P; Puente, C; Haro, C; Bruno, JC; Coronas, A (2023). Bio Oil as Cutter Stock in Fuel Oil Blends for Industrial Applications. Energies, 16(3), -. DOI: 10.3390/en16031485
DOI del artículo: 10.3390/en16031485
Entidad: Universitat Rovira i Virgili
Año de publicación de la revista: 2023
Tipo de publicación: Journal Publications