Articles producció científica> Enginyeria Electrònica, Elèctrica i Automàtica

Interleaved Digital Power Factor Correction Based on the Sliding-Mode Approach

  • Dades identificatives

    Identificador: PC:1468
    Autors:
    Enric Vidal-IdiarteAdria Marcos-PastorAngel Cid-PastorL. Martinez-Salamero
    Resum:
    This study describes a digitally controlled power factor correction (PFC) system based on two interleaved boost converters operating with pulsewidth modulation (PWM). Both converters are independently controlled by an inner control loop based on a discrete-time sliding-mode (SM) approach that imposes loss-free resistor (LFR) behavior on each cell. The switching surface implements an average current-mode controller so that the power factor (PF) is high. The SM-based digital controller is designed to operate at a constant switching frequency so that the interleaving technique, which is recommended for ac-dc power conversion systems higher than 1 kW, can be readily applied. An outer loop regulates the output voltage by means of a discrete-time proportional-integral (PI) compensator directly obtained from a discrete-time small-signal model of the ideal sliding dynamics. The control law proposed has been validated using numerical simulations and experimental results in a 2-kW prototype.
  • Altres:

    Autor segons l'article: Enric Vidal-Idiarte; Adria Marcos-Pastor; Angel Cid-Pastor; L. Martinez-Salamero
    Departament: Enginyeria Electrònica, Elèctrica i Automàtica
    Autor/s de la URV: VIDAL IDIARTE, ENRIC; Adria Marcos-Pastor; CID PASTOR, ANGEL; MARTÍNEZ SALAMERO, LUIS
    Paraules clau: Engineering controlled terms AC-DC power conversion power factor correction
    Resum: This study describes a digitally controlled power factor correction (PFC) system based on two interleaved boost converters operating with pulsewidth modulation (PWM). Both converters are independently controlled by an inner control loop based on a discrete-time sliding-mode (SM) approach that imposes loss-free resistor (LFR) behavior on each cell. The switching surface implements an average current-mode controller so that the power factor (PF) is high. The SM-based digital controller is designed to operate at a constant switching frequency so that the interleaving technique, which is recommended for ac-dc power conversion systems higher than 1 kW, can be readily applied. An outer loop regulates the output voltage by means of a discrete-time proportional-integral (PI) compensator directly obtained from a discrete-time small-signal model of the ideal sliding dynamics. The control law proposed has been validated using numerical simulations and experimental results in a 2-kW prototype.
    Grup de recerca: Grup d'Automàtica i Electrònica Industrial
    Àrees temàtiques: Enginyeria electrònica Ingeniería electrónica Electronic engineering
    Accès a la llicència d'ús: https://creativecommons.org/licenses/by/3.0/es/
    ISSN: 0885-8993
    Identificador de l'autor: 0000-0002-6016-4096; n/a; 0000-0001-8124-6210; n/a
    Data d'alta del registre: 2016-05-02
    Pàgina final: 4653
    Volum de revista: 31
    Versió de l'article dipositat: info:eu-repo/semantics/acceptedVersion
    Enllaç font original: https://ieeexplore.ieee.org/document/7243353
    URL Document de llicència: https://repositori.urv.cat/ca/proteccio-de-dades/
    DOI de l'article: 10.1109/TPEL.2015.2476698
    Entitat: Universitat Rovira i Virgili
    Any de publicació de la revista: 2016
    Pàgina inicial: 4641
    Tipus de publicació: Article Artículo Article
  • Paraules clau:

    Convertidors de corrent elèctric
    Electrònica de potència
    Engineering controlled terms
    AC-DC power conversion
    power factor correction
    Enginyeria electrònica
    Ingeniería electrónica
    Electronic engineering
    0885-8993
  • Documents:

  • Cerca a google

    Search to google scholar